| View previous topic :: View next topic |
| Author |
Message |
pats16vgti
Spends too much time here!
Joined: 05 Apr 2005
Posts: 831
Location: Sicklerville, NJ
|
 Posted: Sun Apr 12, 2009 11:31 am Post subject: 1.8t map sensor pin out? |
 |
|
I have an 01 audi a4 the wires for the map sensor got pulled out during an accident... so i got a new connector and pig tail but the wire colors arent the same.. i need to know what goes where... thanks -pat
new pig tail has:
1.light blue/orange
2. none
3.purple/green
4.purple/ grey
existing wires on my 01 audi a4 are:
black, white/black, blue/grey...
I dont have a bently yet for this year car.. any help would be much appreciated!!!!!!!
_________________
Patrick Doody
1992 jetta gl, 1981 turbo sporttruck, 75 rabbit project |
|
| Back to top |
|
 |
AUTOBOND
Warming up
Joined: 12 Dec 2007
Posts: 90
Location: NORWALK,OH
|
| Posted: Mon Apr 13, 2009 10:19 am Post subject: 1.8t pin out |
|
|
| Looking at alldata did not find map sensor ,how ever did find charge air sensor . Your black ( sw) is the ground pin (kl.) 1 - , your white/black (ws/sw) is pin (kl.)3+ that is your 5 volt ref. ,your blue /grey (bl/gr)is the return to the ecu.pin (kl) 101 . Hope this helps , you can always pm me at our shop ,, jack |
|
| Back to top |
|
|
kilmer420
Spends too much time here!
Joined: 02 Dec 2004
Posts: 398
|
|
| Back to top |
|
|
baddrabbit
Spends too much time here!
Joined: 29 Oct 2007
Posts: 907
|
| Posted: Mon Apr 13, 2009 3:40 pm Post subject: |
|
|
| i have this Bentley at home and can check for ya tonight if i remember.... |
|
| Back to top |
|
|
kilmer420
Spends too much time here!
Joined: 02 Dec 2004
Posts: 398
|
| Posted: Mon Apr 13, 2009 3:45 pm Post subject: Re: 1.8t pin out |
|
|
not sure about your colors but here are the locations on the connector:
pin 1 == GND
pin 2 == Not used
pin 3 == +5v
pin 4 == signal 0-5v |
|
| Back to top |
|
|
pats16vgti
Spends too much time here!
Joined: 05 Apr 2005
Posts: 831
Location: Sicklerville, NJ
|
| Posted: Mon Apr 13, 2009 5:32 pm Post subject: Re: 1.8t pin out |
|
|
| baddrabbit wrote: | | i have this Bentley at home and can check for ya tonight if i remember.... |
that would help tremendously..
| kilmer420 wrote: |
not sure about your colors but here are the locations on the connector:
pin 1 == GND
pin 2 == Not used
pin 3 == +5v
pin 4 == signal 0-5v |
Good info. I will see if my multimeter will point me in the right direction with this one... I know its doing something weird to the way the car runs cause it will stutter at takeoff, and I don't think its making much if any boost at higher rpms... If I understand correctly it reads the boost pressure to warn the ecu if the motor is being over boosted or something to that effect.
_________________
Patrick Doody
1992 jetta gl, 1981 turbo sporttruck, 75 rabbit project |
|
| Back to top |
|
|
pats16vgti
Spends too much time here!
Joined: 05 Apr 2005
Posts: 831
Location: Sicklerville, NJ
|
| Posted: Mon Apr 13, 2009 7:48 pm Post subject: |
|
|
blk: gnd : pin1
wht/blk :+5v : pin3
blue/gray : signal0-5v : pin4
_________________
Patrick Doody
1992 jetta gl, 1981 turbo sporttruck, 75 rabbit project |
|
| Back to top |
|
|
baddrabbit
Spends too much time here!
Joined: 29 Oct 2007
Posts: 907
|
| Posted: Tue Apr 14, 2009 12:48 am Post subject: |
|
|
| glad you got it, cuz i am Bentley Manual RETARDED.... |
|
| Back to top |
|
|
pats16vgti
Spends too much time here!
Joined: 05 Apr 2005
Posts: 831
Location: Sicklerville, NJ
|
| Posted: Tue Apr 14, 2009 12:49 am Post subject: |
|
|
haha me too. bently wiring diagrams and me do not get along... After I found the ground I only had a 50/50 chance of getting the others right haha. no more code for it, and the motor is def running alot more strong. thanks for the help everyone.
_________________
Patrick Doody
1992 jetta gl, 1981 turbo sporttruck, 75 rabbit project |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
